Please note we are still adding products to our new website. Can't see the product you need? Contact us on 01444 243 452 / enquiries@gdrectifiers.co.uk

August 2019 – Dynex’s Press-Pack IGBTs Designed for Robustness, Reliability and Ease of Use

Published on: 30/08/2019

Discover Dynex’s press-pack IGBTs, Robin Simpson talks optimum performance and how important it is that contact pressure is applied uniformly across the device

Dynex's Press-Pack IGBTs by GD Rectifiers

The following article was featured in the April 2019 issue of Bodo’s Power System Magazine, view the original article here (page 34).

 

Introduction

Press-pack IGBTs are an alternative to isolated-base wire-bonded plastic modules, relying instead on pressure contacts. The ease with which press-packs can be stacked makes them the device of choice for applications that require series operation. Their ratings typically extend to higher currents than modules and by using pressure contacts instead of wire bonds and solder joints, they typically benefit form higher reliability. In contrast to wire bonds, which typically fuse and render modules open-circuit in the event of failure, the use of pressure contacts ensures press-packs fail to short circuit. In the event of a high energy failure, their robust housings offer greater rupture resistance than modules [1].

Dynex Press Pack IGBTs by GD Rectifiers 

 

Dynex’s press-pack IGBT products employ a number of novel and cutting edge technologies:

  • Dynamic load-balancing (DLB) technology maximises safe operating area, gives high reliability and improves ease of use compared to conventional press-pack IGBT designs
  • Silver-sinter bonding applied between chip and adjacent molybdenum platelets ensures outstanding reliability and improved thermal performance
  • Silicone edge passivation applied to Dynex’s press-pack chips and a hermetically sealed housing give robust high voltage blocking performance
  • A dedicated auxiliary emitter connection ensures synchronisation of gate drive signals between chips, mitigating the effects of power circuit di/dt on the driver circuit

This article focus’ on Dynex’s DLB technology, how it differs from conventional press-pack IGBT technology and the benefits this offers users in terms of robustness, reliability and ease of use.

 

Importance of contact pressure uniformity

Uniform distribution of contact pressure is vital to ensure optimum sharing of electrical, thermal and mechanical stresses between the chips in press-pack IGBTs to give the largest safe operating area and the highest reliability. Conventional press-pack IGBTs, comprising a hermetic ceramic capsule housing an array of chip assemblies between rigid copper electrodes, have shortcomings in this respect.

Dynex Bodos Power Article Figure 1

Figure 1 illustrates the basic construction of a conventional press-pack IGBT.

The temperature distribution that exists from chip to case within an operating press-pack IGBT drives differential expansion of the housing electrodes, causing them to distort, as shown in Figure 2 This unbalances the distribution of contact pressure and therefore thermal and electrical contact resistances, across the chips [2], [3], significantly reducing the safe operating area and reliability of conventional press-pack IGBTs. It is impossible to avoid electrode distortion, as a temperature distortion will always exist whilst the device is in operation, therefore, a press-pack IGBT design should employ a mechanism to compensate for electrode distortion.

Dynex Bodos Power Article Figure 2

Dynex’s dynamic load balancing mechanism (DLB)

Dynex’s DLB mechanism replaces the rigid pillars of conventional designs with spring assemblies having far greater compliance. The springs are too resistive to form the primary load current path by themselves, so the DLB mechanism incorporates a novel current bypass mechanism, achieved using a flexible conductive diaphragm, as shown in Figure 3a.

 

When the device is clamped, the spring assemblies compress to the height of the spring locator plate at a pre-determined force – the threshold – shown by label 1 in Figure 3b. the clamping force specified in the product datasheet exceeds the threshold force, with the excess force applied to the support frame. This forces pressure contacts between the diaphragm, spring locator and housing electrode – shown by label 2 in Figure 3b – creating a low resistance current path – shown by label 3 in Figure 3c.

The DLB mechanism compensates for any thermomechanical distortion that occurs, ensuring chips are uniformly pressurised, enabling Dynex’s press-pack IGBTs to maintain their large safe operating area and outstanding reliability, under all operating conditions.

 

Dynex Bodos Power Article Figure 3

In addition, the DLB mechanism gives users two further advantages. First, the enhanced mechanical compliance of the device means that heatsinks typically used with thyristors can be used and that onerous flatness tolerances required when using conventional, rigid press-pack do not need to be applied, reducing assembly costs. Second, chips in a Dynex DLB press-pack are protected from over-pressurisation – a risk with conventional press-pack IGBTs – providing extra flexibility in stack assembly procedures, where short-term over-clamping may be required.

 

Safe operating area robustness

Safe operating area ratings for Dynex’s 4.5kV press-pack IGBT range permit operation with line voltages up to 3.4kV and guarantee the capability of the IGBT to turn off over-currents of up to twice the product’s rated current.

 

The products have ultimate capabilities far exceeding their datasheet ratings. To illustrate the robustness of Dynex’s press-pack IGBTs, the following examples are given. Figure 4 shows a Dynex 2.1kA, 4.5kV press-pack IGBT (DPI2100P45A5200) turning off 7.4kA – 3.5 times its rated current – at a line voltage of 3.4kV and a junction temperature of 125°C.

Figure 5 shows the same product withstanding a type-1 short-circuit test performed at a line voltage of 3.4kV and a junction temperature of 125°C for a duration of 40 μs – 4 times industry standard. Figure 6 shows a Dynex 1.6kA, 4.5kv press-pack IGBT (DPI1600P45C3616) withstanding a type-1 short-circuit test with a gate-emitter voltage of 18V, at a line voltage of 3.4kV and junction temperature of 125°C.

 

Dynex press-pack IGBT product range

Dynex is able to supply press-pack IGBTs with a range of industry standard contact diameters from 34mm to 150mm and current ratings from 120A up to 3000A at 4500V. An integrated research and development and manufacturing facility enables chips and devices to be tailored to customers’ applications. Their ease of use, high reliability and robustness has made Dynex press-packs the product of choice for a variety of applications, including HVDC and medium voltage drives.

 

Dynex Bodos Power Article Figure 4

 

Dynex Bodos Power Article Figure 5 

Dynex Bodos Power Article Figure 6 

Conclusion

Press-pack IGBTs are an enabling technology for high current, high reliability applications. Dynex’s dynamic load balancing technology elegantly overcomes the challenges in ensuring the application of uniform contact pressure, giving Dynex’s press-pack IGBTs outstanding robustness and reliability and making them easier to use than conventional designs.

 

For further information on Dynex’s press pack IGBTs you can visit the Dynex website here, or browse their extensive range available at GD Rectifiers here or call our team today on: 01444 243 452.

GD Rectifiers is the UK’s official distributor for Dynex and stock their comprehensive range of high power IGBT modules and FRD modules 

 

Share Article

Related News

Dynex IGBT Modules
Power Electronics for UPS Systems
IXYS IXTY2P50PA
Semikron webinar 2024
Versatile IGBT Power Module
GD Distributor Image
Dynex H1 IGBT Module
Ocram Power Electronics
IXYS high voltage BiOMOSFET product discontinuation
Semikron product discontinuation